Tjernlund 950-1040 24V Relay Kit 8504052 Rev. 3 10/97 Bedienungsanleitung PDF herunterladen

1. The Tjernlund 24V Relay Part #950-1040 may be used as a replacement part or as an added accessory to Tjernlund

Draft Inducers, the MAC-3 controller & IN-FORCER combustion air intakes wired to 24V control circuits. Please refer

to section A of these instructions if installing it as a replacement part and section B if installing it as an accessory part.

2. Terminals 7 and 8 of the 24VAC Relay are rated for an input of 24VAC only! DO NOT APPLY 115VAC TO

TERMINALS 7 AND 8 OF THE RELAY.

Disconnect 115VAC power from the Power Venter before continuing. All wiring from the Power Venter to the appliance

must be appropriate class 1 wiring as follows: installed in rigid metal conduit, intermediate metal conduit, rigid non-metallic

conduit, electrical metallic tubing, Type MI Cable, Type MC Cable, or be otherwise suitably protected from physical damage.

SECTION A

1. Remove the electrical box cover plate of the Power Venter.

2. Place the replacement relay next to the defective relay located in the Power Venter electrical box.

3. One by one, remove the wires from the defective relay and connect them to the corresponding terminal on the

replacement relay.

4. Carefully drill the rivets out that are holding the defective relay to the junction box.

5. Install the replacement relay in the electrical box and secure it with the nuts/screws provided, (See Diagram A).

6. Reestablish power to the Power Venter and equipment. Run equipment through a couple of heating cycles to verify

proper operation.

7. If defective relay failed within the one year warranty period, you may return it along with proof of purchase to the

Tjernlund Distributor it was originally purchased from for a full refund.

SECTION B

1. Remove the electrical box cover from the Power Venter/Draft Inducer.

2. Secure the relay to the inside of the electrical box using the nut/screw provided, (See Diagram A).

3. Wire the relay according to the appropriate diagram on back of this page for your installation.

4. Run equipment through a couple of heating cycles to verify proper operation.

OWNERS INSTRUCTIONS

THESE INSTRUCTIONS MUST

REMAIN WITH EQUIPMENT

DO NOT DESTROY

ALWAYS FOLLOW HEATER MANU-

FACTURER’S INSTRUCTIONS FOR

PROPER OPERATION OF HEATER

AND RE-LIGHTING OF PILOT

READ INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION

(950-1040) 24VAC RELAY INSTALLATION INSTRUCTIONS

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794

PHONE (651) 426-2993 • (800) 255-4208 • FAX (651) 426-9547

Visit our web site • www.tjernlund.com

DIAGRAM A

1 2

TJERNLUND PRODUCTS, INC 1
950-1040 2

Inhaltsverzeichnis

Seite 1 - TJERNLUND PRODUCTS, INC

1. The Tjernlund 24V Relay Part #950-1040 may be used as a replacement part or as an added accessory to Tjernlund Draft Inducers, the MAC-3 controlle

Seite 2 - 950-1040

TYPICAL 24V GAS ELECTRONIC IGNITION WIRING WITH POWER VENTER/DRAFT INDUCERNOTEIF YOUR ELECTRICAL DIAGRAM IS NOT INCLUDED, CONTACT OUR CUSTOMER SERVICE

Kommentare zu diesen Handbüchern

Keine Kommentare

Tjernlund 950-1040 24V Relay Kit 8504052 Rev. 3 10/97 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Tjernlund 950-1040 24V Relay Kit 8504052 Rev. 3 10/97 herunter. Tjernlund 950-1040 24V Relay Kit 8504052 Rev. 3 10/97 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Tjernlund 950-1040 24V Relay Kit 8504052 Rev. 3 10/97